problème de version de Wireless Extension pour sagem xg-703a

Bonjour à tous,

Ca fait quelques jours (et nuits;o) que je me bats avec mon dongle sagem xg-703a sur ma gentoo 2005.1 (kernel 2.6.12-gentoo-r9)
avec ndiswrapper 1.2 (installé avec emerge).
J'ai pris le driver issu de "Utilitywifixg703a 80211g.zip". J'ai fait un diff avec le driver du DVD de la livebox, c'est exactement le même. Je suis le tuto de GUIGUI...


> ndiswrapper -i ./WlanUIG.inf
Installing wlanuig
Parse error in inf. Unable to find section COMMON_NDIS_REG_NT
no dev WLAN_USB2.NT.5.1 NT.5.1
(Bon là je ne m'inquiète pas, y a la même chose dans le tuto...)

> modprobe ndiswrapper

/var/log/messages donne ça...
Dec 20 19:13:01 TITAN ndiswrapper version 1.2 loaded (preempt=no,smp=no)
Dec 20 19:13:02 TITAN usbcore: registered new driver ndiswrapper

Là je branche le dongle

/var/log/messages donne ça...
Dec 20 19:14:17 TITAN hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0004
Dec 20 19:14:17 TITAN ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
Dec 20 19:14:17 TITAN hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
Dec 20 19:14:17 TITAN hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
Dec 20 19:14:17 TITAN ehci_hcd 0000:00:13.2: port 2 high speed
Dec 20 19:14:17 TITAN ehci_hcd 0000:00:13.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
Dec 20 19:14:17 TITAN usb 1-2: new high speed USB device using ehci_hcd and address 7
Dec 20 19:14:17 TITAN ehci_hcd 0000:00:13.2: port 2 high speed
Dec 20 19:14:17 TITAN ehci_hcd 0000:00:13.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
Dec 20 19:14:17 TITAN usb 1-2: default language 0x0409
Dec 20 19:14:17 TITAN usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=3
Dec 20 19:14:17 TITAN usb 1-2: Product: USB Device
Dec 20 19:14:17 TITAN usb 1-2: Manufacturer: GlobespanVirata
Dec 20 19:14:17 TITAN usb 1-2: SerialNumber: 3887-0000
Dec 20 19:14:17 TITAN usb 1-2: hotplug
Dec 20 19:14:17 TITAN usb 1-2: adding 1-2:1.0 (config #1, interface 0)
Dec 20 19:14:17 TITAN usb 1-2:1.0: hotplug
Dec 20 19:14:17 TITAN ndiswrapper 1-2:1.0: usb_probe_interface
Dec 20 19:14:17 TITAN ndiswrapper 1-2:1.0: usb_probe_interface - got id
Dec 20 19:14:17 TITAN ndiswrapper: driver wlanuig (Sagem SA,06/03/2004, 3.0.18.2) loaded
Dec 20 19:14:22 TITAN wlan0: ndiswrapper ethernet device 00:60:b3:c5:84:b4 using driver wlanuig, configuration file 0CDE:0008.0.conf
Dec 20 19:14:22 TITAN wlan0: encryption modes supported: WEP, WPA with TKIP, WPA with AES/CCMP
Dec 20 19:14:22 TITAN net.agent[10991]: add event not handled

??? C'est grave docteur le "add event not handled"; C'est l'ajout de mon dongle ???

> iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

sit0 no wireless extensions.

Warning: Driver for device wlan0 recommend version 18 of Wireless Extension,
but has been compiled with version 17, therefore some driver features
may not be available...

wlan0 IEEE 802.11g ESSID:off/any
Mode:Managed Frequency:2.462 GHz Access Point: 00:00:00:00:00:00
Bit Rate:2 Mb/s Tx-Power:32 dBm
RTS thr:2347 B Fragment thr:2346 B
Encryption key:off
Power Management:off
Link Quality:100 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:15 Missed beacon:0

??? Là me faut il une autre version de ndiswrapper ou un package (emerge -s wireless-extension ne me donne rien) ???
Je continue pour vous donner le plus d'info possible...

> iwlist wlan0 scan
Warning: Driver for device wlan0 recommend version 18 of Wireless Extension,
but has been compiled with version 17, therefore some driver features
may not be available...

wlan0 Scan completed :
Cell 01 - Address: 00:03:C9:71:47:B4
ESSID:"Wanadoo_xxxx"
Protocol:IEEE 802.11g
Mode:Managed
Frequency:2.457 GHz (Channel 10)
Quality:0/100 Signal level:-60 dBm Noise level:-256 dBm
Encryption key:on
Bit Rate:1 Mb/s
Bit Rate:2 Mb/s
Bit Rate:5.5 Mb/s
Bit Rate:11 Mb/s
Bit Rate:6 Mb/s
Bit Rate:9 Mb/s
Bit Rate:12 Mb/s
Bit Rate:18 Mb/s
Bit Rate:24 Mb/s
Bit Rate:36 Mb/s
Bit Rate:48 Mb/s
Bit Rate:54 Mb/s
Extra:bcn_int=100
Extra:atim=3

>iwconfig wlan0 channel 10 mode managed ESSID "Wanadoo_xxxx" key "xxxxxxxxxxxxxxxxxxxxxxxxxx"

iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

sit0 no wireless extensions.

Warning: Driver for device wlan0 recommend version 18 of Wireless Extension,
but has been compiled with version 17, therefore some driver features
may not be available...

wlan0 IEEE 802.11g ESSID:off/any
Mode:Managed Frequency:2.457 GHz Access Point: 00:00:00:00:00:00
Bit Rate:2 Mb/s Tx-Power:32 dBm
RTS thr:2347 B Fragment thr:2346 B
Encryption key:xxxx-xxxx-xxxx-xxxx-xxxx-xxxx-xx Security mode:restricted
Power Management:off
Link Quality:100 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:80 Missed beacon:0

Bref toujours pas d'ESSID l'access point n'est pas renseigné...
Inutile de dire que dhcpcd ne me donne aucune adresse IP !!!

Pour info, j'ai une connexion ethernet mais je voudrais me passer du cable qui descend l'escalier. Faut il que ma liaison ethernet soit coupée pour configurer le wifi ?

Là je sèche, toute aide sera la bienvenue, un grand MERCI d'avance à ceux qui prendront le temps de me filer un coup de main !!!